The PARIS Forums


Home » The PARIS Forums » PARIS: Classifieds » FS or FT: Ensoniq PARIS DAW System, various pieces - MEC chassis, input cards, control 16 (As new from college surplus)
FS or FT: Ensoniq PARIS DAW System, various pieces - MEC chassis, input cards, control 16 [message #103582] Tue, 23 June 2009 05:07 Go to next message
corran is currently offline  corran   UNITED STATES
Messages: 4
Registered: June 2009
Location: 31602
Junior Member
.

Thank you in advance

Doros

PS

please give me a shipping cost to CYPRUS.
What you like to do ?
The 8 Input Card into first Mec ?
In this case you don't need a second mec.
If you like to take a two card system to record, you need a 2nd mec.

I have ribbons for connecting 2 EDS with each other too.

I will check the shipping coast to cyprus

Best regards
Dan

I need a second eds1000 and a second Control16 for sure

So please advice about connections. Do i need a second MEC?You don't necessarily need a second MEC, you can run a two card system with a single MEC - if you just have one, the audio from both EDS cards is pre-mixed and flows through it.

Getting a second MEC is really about getting more inputs and outputs (MECs are limited to 20 active channels of i/o at a time - the built in i/o plus two active cards (say an ADAT card and an 8i, or any other combination). You can have eight cards in one MEC, but only two can be active at one time.Thanks Kerry. Will see whats needed to get a nice expansio pack for my Paris system.Dan,
Are you selling off you whole PARIS rig?
If yes, what are you jumping to?@Will
not the whole Paris Stuff, but i have buyed a lot of Stuff in the past.Some Stuff i have lease to friend and get it back now.
I have "jumped" to Universal Audio Apollo now.
So my Setup today is :
Apollo Quad
1x Paris MEC /2 Adat/ 8 input / 8 output
RME 9652
RME 9632
Universal Audio UAD2 Quad
UA Twin Finity 4710d
UA Compressor 1176ae
to go into DAW. With Paris i have 32 I/O. Thats enough, i have decided !
In the Past were 16 I/O Adats in my DAW blocked by E6400 Sampler. I will rout them over RME 5652 into my System.
I have used two 4710d going into second MEC.
The Third MEC was fillend by other Romplers (Proteus 1000 & 2x2000, An1x,X3,ChaosPad)and so on.
Apollo is real good. The special is, you can use your plugins in realtime !

Have a
  • Attachment: Img_3557.jpg
    (Size: 166.24KB, Downloaded 3876 times)
  • Attachment: Img_3558.jpg
    (Size: 182.60KB, Downloaded 4701 times)
  • Attachment: Img_3559.jpg
    (Size: 132.48KB, Downloaded 3316 times)
  • Attachment: Img_3560.jpg
    (Size: 146.43KB, Downloaded 3524 times)

[Updated on: Thu, 01 October 2009 19:21]

Report message to a moderator

Re: FS or FT: Ensoniq PARIS DAW System, various pieces - MEC chassis, input cards, control 16 [message #103584 is a reply to message #103582] Tue, 23 June 2009 09:41 Go to previous messageGo to next message
kerryg is currently offline  kerryg   CANADA
Messages: 1529
Registered: February 2009
Senior Member
Administrator
nice Weekend everyone.


@Kerry
THX to Kerry...for "You don't necessarily need a second MEC, you


"... being bitter is like swallowing poison and waiting for the other guy to die..." - anon
Re: FS or FT: Ensoniq PARIS DAW System, various pieces - MEC chassis, input cards, control 16 [message #103586 is a reply to message #103584] Tue, 23 June 2009 15:03 Go to previous messageGo to next message
corran is currently offline  corran   UNITED STATES
Messages: 4
Registered: June 2009
Location: 31602
Junior Member
can run a two card system with a single MEC - if you just have one, the audio from both EDS cards is pre-mixed and flows through it. ", thats exactly what i like to say !

Re: FS or FT: Ensoniq PARIS DAW System, various pieces - MEC chassis, input cards, control 16 [message #103596 is a reply to message #103586] Thu, 25 June 2009 08:48 Go to previous messageGo to next message
corran is currently offline  corran   UNITED STATES
Messages: 4
Registered: June 2009
Location: 31602
Junior Member
/>
http://www.ebay.com/itm/181884072383?ssPageName=STRK:MESELX: IT&_trksid=p3984.m1555.l2649

I also have an MEC with an 8 input card and a number of Control 16s if anyone is interested.

Thanks,
PeteIm interested in purchasing an eds card the Mec and possibly a c16. pls pm me the prices. Thank youIf you have an extra output card you don't need please let me knowHi folks - if you have an 8i card and/or an ADAT card for sale (and are within reasonable shipping dist
Re: FS or FT: Ensoniq PARIS DAW System, various pieces - MEC chassis, input cards, control 16 [message #103650 is a reply to message #103596] Thu, 02 July 2009 06:31 Go to previous message
corran is currently offline  corran   UNITED STATES
Messages: 4
Registered: June 2009
Location: 31602
Junior Member
e's wants that it's all sold, I could split it up. If not, I'd need to decide
Previous Topic: FS: Brian dvd and Paris foot switch WTB: 8-in card
Next Topic: WTB: Paris instructional DVD?
Goto Forum:
  


Current Time: Thu May 07 04:18:52 PDT 2026

Total time taken to generate the page: 0.06368 seconds