| OT: Pro Tools V 6.9 Sounding Pretty Darm Good These Days [message #60689] |
Sun, 27 November 2005 19:00  |
LaMont
Messages: 828
Registered: October 2005
|
Senior Member |
|
|
. So, I know =
>my clock=20
> is good, the<BR>cards are good, the MECs and interfaces are good. I=20
> just<BR>brought up V2.2 to double check, and recorded using=20
> the<BR>interfaces that don't work with 3.0, so it's definatley<BR>a
=
>3.0=20
> issue.<BR><BR>When you had to have your MECs on A and C (or E), was=20
> that<BR>with Version 2.2 and 3.0, or just with 3.0? I could try=20
> moving<BR>the MEC to C and see if that fixes it, but I dread making=20
> any<BR>changes at all to a functional (under 2.2) PARIS=20
> system......<BR><BR><BR>"Tom Bruhl" <<A=20
> href=3D"mailto:arpegio@comcast.net">arpegio@comcast.net</A>>=20
> wrote:<BR>><BR>><BR>>Dead,<BR>>What Aaron says is =
>true. =20
> When my system was three cards with two Mecs<BR>>I had card A and =
>C=20
> attached to the Mecs. Now with five cards it's A =
>and<BR>=3D<BR>>E.=20
> =3D20<BR>>My ASUS boards like the first and last card when using =
>two=20
> Mecs.<BR>>Tom<BR>> "Aaron Allen" <<A=20
> href=3D"mailto:Report message to a moderator
|
|
|
|
|
|
| Re: OT: Pro Tools V 6.9 Sounding Pretty Darm Good These Days [message #60826 is a reply to message #60689] |
Thu, 01 December 2005 15:49  |
Jamey Tiffee
Messages: 17
Registered: November 2005
|
Junior Member |
|
|
gt;>I detect though that card 1 (slot1) is identified as card B, card 4 (slot
>>>>5) is identified as card A (main card)
>>>>So due to someone's last post here should I connect as Paris sees the
cards
>>>>or as I see them inside my computer?
>>>>Paris works ok but maybe I am risking or could have more stable setup
(nothing
>>>>major though)
>>>>Regards,
>>>>Dimitrios
>>>
>>As long as all the cards are connected correctly (10 pin cables
straight across and 16 pin cables crossed), and the Paris software
plays back on all submixes, it doesn't matter.
I simply start at one end of the EDS cards and stagger the 16 pin
ribbons.. bottom (first card) right to second left, second right to
third left, third right to fourth left, fouth right to fifth left,
fifth right to first left. I then find the master (A) card. One that
is done I finde the order of the remaining cards (which it sounds like
you have already done) and make sure I have one interface on the first
and last card.
So far, it has always worked.
David.
Dimitrios wrote:
> Hey David,
> Maybe I did not made things clear.
> It is not Mecs where to get attached.
> I have three mecs hanging over card A, B, and D.
> It is the interconnecting cables over pci cards thatI am worried about.
> Regards,
> Dimitrios
> EK Sound <spamnot.info@eksoundNO.com> wrote:
>
>>Hey Dimitrios,
>>
>>It doesn't matter how the computer sees them... hang you MEC's off of
>>A and D (assuming you only have two interfaces) and you should be g
|
|
|
|
|
|
|
|
The PARIS Forums
Search
Help
Members
Register
Login
Home
